Fluoro untying? - Page 2 - Fly Fishing Forum
Lines, Loops and Leaders Line / Leader Recipes, Loops, Splices, etc.

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #16  
Old 09-01-2007, 10:17 AM
mikez mikez is offline
Registered User
 
Join Date: Oct 2001
Location: Popham Beach to Watch Hill
Posts: 407
Just to add my unsolicited $0.02...
I dislike flouro in general because of abrasion sensitivity - you have to frequently run it between your fingers and aggressively cut and replace any rough patches. This becomes a chore when fishing rough terrain such as jetties, rock piles etc.
For that reason I have limited my use of flouro to times when I am targeting line shy tunoids, most often false albacore.
Having said that, I find it strange that I have never run into the knot problems that so many attribute to flouro. I have had flyshop dudes tell me flat out "You CAN NOT" use blood knots, clinch knots etc. Never being one to listen to the voice of authority, I ignored them and stick to the knots I learned when I was 10.
I ONLY use blood knots to attach flouro tippet to mono leader and I only use improved clinch to attach flies. Now before I go on, let me just clarify that this choice is more personal preference and not meant to endorse specific knots. Your milage will almost certainly vary.
Nevertheless, I have hooked dozens of fast moving tunoids and landed a fair percentage of those and NEVER ONCE has either a blood knot or clinch knot in flouro failed me. This is saying alot as I fish mostly from shore and use mostly 12 lb tippet. That makes for a prolonged tug o' war with lots of extreme exceleration. In other words, a really good test for the knots.
On those few occasions when I break one off, invariably it is either an abraded patch in the flouro or a wind knot.
As someone else mentioned, tying technique is critical. A poorly tied knot will fail first, no matter what kind it is.
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #17  
Old 09-01-2007, 12:54 PM
teflon_jones's Avatar
teflon_jones teflon_jones is offline
Registered User
 
Join Date: Jan 2005
Location: Colorado Front Range
Posts: 1,310
Send a message via AIM to teflon_jones Send a message via Yahoo to teflon_jones
I regularly use 7x tippet with an improved clinch knot (for almost 20 years now) and rarely have it come untied. Frog Hair is my normal tippet too. If it does come untied, it's usually because I haven't done enough twists or because I didn't check the knot after I landed the last fish or pulled the fly off of a snag...
__________________
My passion for catching fish is eclipsed only by the fish's passion not to be caught.
Scott
Reply With Quote Quick reply to this message
  #18  
Old 09-02-2007, 09:11 AM
petevicar's Avatar
petevicar petevicar is offline
In moderation
 
Join Date: Dec 2004
Location: The seven seas
Posts: 840
When I first used fluoro, when bonefishing, I was continuously loosing flies. I then worked out that a clinch knot is a very bad knot for fluro.
I now tie my flies on with a uni knot and have no problems.

Pete
Reply With Quote Quick reply to this message
  #19  
Old 09-03-2007, 04:11 PM
chromedome chromedome is offline
chromedome
 
Join Date: Feb 2005
Location: NIAGARA
Posts: 140
I suspect Juro is right about the high strength of the palomar knot. However, I don't use it since in my hands at least, it uses up too much tippet. I ran a few tests in 2006 convincing me to give the orvis knot a try. It is now my knot of choice with tippets ranging from 2X thru 0X for the steelies I target. I also prefer the orvis leader to tippet knot over the surgeons knot although its a tad harder to tie.
Reply With Quote Quick reply to this message
  #20  
Old 09-04-2007, 07:33 PM
mikez mikez is offline
Registered User
 
Join Date: Oct 2001
Location: Popham Beach to Watch Hill
Posts: 407
Quote:
Originally Posted by petevicar
I then worked out that a clinch knot is a very bad knot for fluro.
Pete
It's strange that we could have such divergent points of view about something that is not subjective. Either the knots fail, or they don't right?
For whatever reason, mine don't. I'm not being argumentitive, it's not important to me what knot someone else uses. I'm just curious why my experiences don't match what I've heard elsewhere.
Yesterday morning I hooked this false albacore from a popular, crowded jetty. The fish ran along the jetty in front of several surf casters. At least four of them hooked my line and preceded to "set the hook" when they felt the tension of my line causing very severe jerks on the leader. The fish also ran around a lobster bouy line and pulled the bouy almost under. I had no hope of landing the fish and expected the line to part at any moment. Somehow I disentangled from the other lines and the fish freed itself from ther pot warp. I then horsed the fish in before it got in any more trouble. I considered that to be about the most punishment I could inflict on my terminal tackle without outright breaking the leader itself. The flouro I used is the Vanish line by Berkely. The knot was an improved clinch with six turns. A blood knot was used to attach flouro to mono. According to conventional wisdom, I should have never landed that fish To me it was a normal day.
Reply With Quote Quick reply to this message
  #21  
Old 09-06-2007, 01:18 AM
chromedome chromedome is offline
chromedome
 
Join Date: Feb 2005
Location: NIAGARA
Posts: 140
Is it possible that while the clinch or improved clinch is one of the simplest knot to learn to tie, it is also one that is prone to inconsistencies in the tying process? I'm not sure if that expresses it exactly as I mean to, but maybe there are subtle aspects one has to pay attention to in tying the knot to get it to come out the same each time. Things like getting exactly the same number of turns before turning in the tag end, or how much one pulls on the tag end at the completion of the knot, can make a difference. I really didn't think about this till I started using the Orvis knot. Even tho the Orvis knot is somewhat harder to learn to tie, compared to the clinch knots I don't think there is as much chance for variation in tying it from one knot to the next providing you stick to the basic procedure for tying the knot.
Reply With Quote Quick reply to this message
  #22  
Old 09-06-2007, 07:41 PM
mikez mikez is offline
Registered User
 
Join Date: Oct 2001
Location: Popham Beach to Watch Hill
Posts: 407
Don't know why I'm obsessing over this...
Back out in albie land today, after landing one hard pulling long running football, purposly neglected to retie. Wanted to see how many fish I could get on the one clinch knot [I normally retie frequently].
Number two, after several long hard runs, wrapped me around the dreaded lobster bouy. Next followed the tug o' war as I tried to free the fish from the pot line while it made runs against the rope with maybe four feet of leader. The runs were hard enough to pull the bouy under. Somehow the fish came free and I landed it.
Same exact scenario with number three except try as I might, I could not free the fish from the damn bouy. After seriously considering swimming for it [it was down too deep on the rope], I had no choice but to pull until the leader broke. The blood knot between mono and flouro held and the tippet broke close to the fly. Although I don't know for sure if the clinch knot broke, the end of the tippet was frayed for about three inches. I believe it was abrasion and not the knot which broke.
Flouro was again the Vanish brand @ 12#, improved clinch, six turns.
Not sure what I proved but I believe I got this out of my system.
Now if somebody would just invent an invisible tippet material that could cut through rope, I'd have it made.
Reply With Quote Quick reply to this message
  #23  
Old 09-07-2007, 07:49 AM
Vince's Avatar
Vince Vince is offline
*** FORUM SPONSOR ***
 
Join Date: Sep 2004
Location: Western New York Steelhead, Bahamas Bonefish, Wild Western Trout
Posts: 496
I have no problems with a clinch knot and flouro, both in salt and fresh. I moisten it, and pull it tight slowly, and then put pretty good pressure on it to tighten it down. No sharp tugging pressure, but a slow steady pressure. I believe as Chromedome said, it all about tying it properly.

If you read Chico Fernandez's book Fly Fishing for Bonefish, when not using a loop to attach the fly, he uses an 7 or 8 turn clinch knot, and he has tested it against an improved clinch and with 8 turns it came out stronger. A simple clinch knot is all you need if tied properly. He says an 8 turn clinch tests at 99-100%.
__________________
Vince Tobia
Forum Sponsor
Cattaraugus Creek Outfitters
God does not deduct from man's alloted time the hours spent fishing.
Reply With Quote Quick reply to this message
  #24  
Old 09-23-2007, 12:33 PM
burk burk is offline
Registered User
 
Join Date: Oct 2002
Location: PM, Betsie, Elk Creek
Posts: 28
I've been using Seagar flouro for tippets on Salmon and Steelhead in the Great Lakes for a few years now and have had zero knot failures. I use cinch knots, but I use a small swivel, as I get tiered of tying blood knots for leaders in January in MI. I agree that abrasion resistance is an issue, and I do check my line after each hook up. The one thing I disagree on is lubricating the knot. Knots slip because they aren't pulled tight, also Flouro Carbon is very abrasive when dry. Lubricating your knots keeps it from cutting into itself and allows you to pull the knot TIGHT. A dry pull will cut into the line as it's pulled and won't cinch up as tight. I rarely leave much tag end, tie conventional cinch knots because they're fast, and I don't loose fish because of bad knots.
This was last Wed. on a 8 lb leader with a Spey rod under an indicator.[IMG][/IMG]
Reply With Quote Quick reply to this message
  #25  
Old 09-23-2007, 03:34 PM
Galong's Avatar
Galong Galong is offline
Registered User
 
Join Date: Aug 2007
Location: Earth
Posts: 66
Wow Burk, what an awesome fish! Thanks for the pic. That's a dream fish for me. I'd love to catch even a much smaller one.
Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Looking for Stren fluoro 6 lb shad For Sale by Owner 2 10-23-2006 03:08 PM


All times are GMT -5. The time now is 10:36 AM.



Copyright Flyfishingforum.com (All Rights Reserved)