Winterizing - Fly Fishing Forum
Propwash A boat is a hole in the water into which you pour... good times!

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #1  
Old 11-14-2006, 12:25 PM
Smcdermott's Avatar
Smcdermott Smcdermott is offline
Jonesin...
 
Join Date: Mar 2002
Location: Rhode Island
Posts: 1,220
Winterizing

Well unfortunately it is that time of year again when we will need to put our boats to bed for the winter. What are your plans this year? There has been a lot of debate as to whether you should fill your tank or leave it as close to empty as possible with the new ethanol blends. My original plan was to leave my tank as empty as possible with the remaining fuel treated with Startron stabilizer. It seems to me the biggest issue is octane loss and the water absorption not as serious as originally thought. As circumstances would have it my boat is being left in NC at the factory for a good portion of the winter to have some cosmetic warranty work done as well as a few upgrades (additional rod racks and moving the fuel/water separator). NC does not use Ethanol so I will have to wait until next year to make any necessary Ethanol adjustments but I did run the tank down and use Startron for the full week I was in Harkers. Very interested to hear what you have done/plan to do. We can then share how it all worked out next year.

Sean
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old 11-14-2006, 01:06 PM
Dble Haul's Avatar
Dble Haul Dble Haul is offline
Fly chucker
 
Join Date: Aug 2001
Location: New England
Posts: 3,674
All I have ever done with my outboard (1990 40hp Evinrude) is top off the gas tank and add fuel stabilizer. I then run the outboard for about five minutes with the hose muffs attached to distribute the stabilizer, and I'm done.

This will be my fourth year doing it this way, and my engine has always started on the first crank in the spring. My fuel tank only holds six gallons, so your mileage may vary (pun intended).
__________________
Mark
Reply With Quote Quick reply to this message
  #3  
Old 11-14-2006, 02:30 PM
GregD's Avatar
GregD GregD is offline
2 handed Fly Chucker
 
Join Date: May 2000
Location: Massachusetts, Rhode Island
Posts: 638
Hi Guys,

Yup it's about that time of year again. I never seem to get it done till the snow begins to fly. I usually add stabilizer and have the tank near full. Supposedly cuts down on condensation in the tank. It's always a good idea to fog the carberators to cut down on rust in the cylinders and varnish in the carbs if you don't have injectors. Not a bad Idea to use old spark plugs for this as the plugs take a bath too.

Johnson and evinrude have shrader valves that make it very easy to do the job yourself. I'll be doing my new mercs later after bringing it my new boat back from florida by way of Harkers. I expect the have something similar in regards to fittings for fogging the carbs and cylinders.

Greg.
Reply With Quote Quick reply to this message
  #4  
Old 11-18-2006, 03:20 PM
Slinger's Avatar
Slinger Slinger is offline
CantAnchorUs
 
Join Date: Jan 2002
Location: Rhode Island
Posts: 733
My Whaler has 2, 9 gallon tanks. One was left full and treated with Stabil, the other was run dry and left empty. Ran the Stabil all thru the system and fogged the hell out of the motor. Pulled the batteries and wrapped with a tarp. I`ve never had a problem in the spring done this way. Then again it`s only 4 months before the boat gets back into action with the early holdovers.
Slinger
__________________
Steve
Reply With Quote Quick reply to this message
  #5  
Old 11-19-2006, 08:11 AM
JimW JimW is offline
Registered User
 
Join Date: Feb 2000
Location: As long as it's Salty
Posts: 1,795
I've got an 85 gallon tank so it's tempting to tap the cheap gas prices and fill 'er up. I talked to the folks at Monahans and was told if you've got a plastic tank leave it empty as possible. Aluminum might get some corrosion if you leave it low all winter but if you fill it the octane loss may be an issue and you could be sputtering for the first few trips, not so great for the engine.
I've got 10 gallons left with a double shot of the Johnson 4+2 treatment which I run all season at the recommended mix.

Fogged it yesterday. Don't forget to grease all the zerks to push out any water. I also spray the CRC version of wd-40 all over the engine and grease any exposed moving parts. Wipe down the greased parts in the Spring and there should be no corrosion. Drain and refill the lower unit gear oil, no milk this year so my seal job is holding up well. Probably time for a water pump job but I think that will have to wait until Spring.
Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Winterizing the two hander Scott K Pacific Northwest Sea Run Forum 13 11-28-2002 07:58 PM


All times are GMT -5. The time now is 04:13 PM.



Copyright Flyfishingforum.com (All Rights Reserved)