Cut-to-length tubes for tube flies - Fly Fishing Forum
>> Archive: Salmon & Steelhead Flies Spey flies to mixed wings, new innovations

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #1  
Old 11-09-2006, 12:50 PM
DBenner DBenner is offline
Registered User
 
Join Date: Jan 2006
Location: Miramichi, New Brunswick
Posts: 17
Cut-to-length tubes for tube flies

Hi there,

After just finishing some flies on the cut-to-length tubes I got to thinking about how they looked compared to some pictures I have as patterns (and I need to buy more tubes also, the sample packs I had are gone). After you cut an inch off the cut-to-length tube, I found my cuts were a little rough so I heated them with a cigarette lighter and formed them by shoving a finish nail up the tube to even out the cut and put a little flange on the end of the tube.

What have you found to be the best tool to cut the tube initially to reduce the roughness of the cut? What do you use to get that all round nicely formed flange on the end so the leader does not fray? Do you flange both ends? I was thinking maybe the nail was not the right idea, maybe another tool would be better..

Thanks alot, tubes are relatively new to me so I am still learning.

Dwight
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old 11-09-2006, 01:43 PM
Charlie's Avatar
Charlie Charlie is offline
Moderator
 
Join Date: Oct 2003
Location: Eastern Great Lakes & Gaspe
Posts: 1,003
Dwight,

I use a razor blade to cut mine. And I use a nail or a pin to aide me when I am heating them up to form the flange on the end of the tube same as you. I usually do this on both ends of the tube. However, plastic tubes will usually not fray your tippet, especially the scandinavian stuff. It is fairly soft and will knot cut the leader. Hope this helps.

Charlie.
__________________
Release-em-Alive!
Reply With Quote Quick reply to this message
  #3  
Old 11-09-2006, 03:31 PM
juro's Avatar
juro juro is offline
Coast2coast Flyfishaholic
 
Join Date: Jan 2000
Location: Steelhead country|striper coast|bonefish belt
Posts: 20,585
Lay the tube on a cutting surface (wood, cuttingboard etc)

Put the razor edge down on it.

Roll the tube sideways.

voila!
__________________
IFFF Certified THCI @ 2005
Capeflyfisher Guide Service
Island Hopper, Guitarist, Incurable Dreamer
and Founder, Worldwide Flyfishing Forum
Reply With Quote Quick reply to this message
  #4  
Old 11-09-2006, 03:33 PM
JimT JimT is offline
Registered User
 
Join Date: Sep 2004
Location: Great Lakes
Posts: 7
Dwight,

I use a single edge razor blade to cut mine. To get a square end; I made a jig by drilling a hole in a piece of wood (needs to be a snug fit and square to the surface), slide the tube in the hole and use the wood block surface to slide the razor along and push through the tube. I then us a lighter or candle and twirl the end of the tube (free hand) close to the flame. A small burr forms in ID and I remove this with an Exacto knife. The whole process takes a few seconds. The key to a uniform, good looking flare, whatever method you use, is to get a square end.


Jim T
Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Tube fly length vs. hook sizes DBenner >> Archive: Salmon & Steelhead Flies 2 04-12-2006 05:25 AM
Tube Flies - The junction tube skip_scratch >> Archive: Salmon & Steelhead Flies 3 12-04-2005 06:53 PM
tube flies wet fly Pacific Northwest Sea Run Forum 17 12-25-2003 03:42 PM


All times are GMT -5. The time now is 02:05 AM.



Copyright Flyfishingforum.com (All Rights Reserved)