rod cleaning - Fly Fishing Forum
Gear Talk - Fly Stuff Spoken Here Sage advice & fresh perspectives

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #1  
Old 11-16-2000, 01:39 PM
jeffg jeffg is offline
Active Member
 
Join Date: Feb 2000
Location: Boston
Posts: 203
rod cleaning

No not reels, what do folks clean their rods with? Fly rods, trolling rods, spin rods, whatever...

I have been using plain old pledge on my rods with glassy coatings, and have always assumed I am not damaging the coating with the polishing chemicals--it tends to leave a little waxy finish that I figured was probably good. I am a little more apprehensive on rods with that plain graphite finish, like some fly rods or some of the loomis/st. Croix spinners. Any thoughts? Reel seats and guides all get Boeshield blasts, which also usually tends to get on the rods as well...I assume to no detriment?

Jeff
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old 11-16-2000, 02:50 PM
RayStachelek's Avatar
RayStachelek RayStachelek is offline
Registered User
 
Join Date: Oct 2000
Location: Rhode Island & beyond
Posts: 720
RE:rod cleaning

Pledge is a fine product to use on most rod finishes. Before you apply the polish, just make sure of several steps. The rod should be thoroughly cleaned. Mild dish washing detergent will do the job. Use an old tooth brush or any soft brush to reach the hard to get to places where salt/corrosion buildup will occur both on the blank and reel seats.

Check the thread raps, clear coats for cracks, even run your fingers through the guide and check for sharp edges and loose ceramics inserts. Check guide feet also. Now's the time, if you have to, to send it in for repairs. This way it will be ready for spring.

Storing it is your last concern. Place it in the sock and tube and you should be all set. Never keep it strung or store it horizontally if it can be avoided. In the spring put a little paraffin wax or dubbing wax on the ferrule.
Reply With Quote Quick reply to this message
  #3  
Old 11-16-2000, 06:07 PM
juro's Avatar
juro juro is offline
Coast2coast Flyfishaholic
 
Join Date: Jan 2000
Location: Steelhead country|striper coast|bonefish belt
Posts: 20,593
RE:rod cleaning

Jeff - hangin' the old striper stick up for the winter, eh?

When I get ambitious I give my good rods a little soak in the tub, then a little scrub with soapy water, rinse and dry. I've heard that furniture polish is what manufacturers use to restore luster, and I have used it without noticing any ill effects. Honestly though, I don't polish them often. I think I've done it once or twice in my life.

Anyway, I suspect turtle wax would be a good choice too - it reduces ultraviolet rays and all that. Never tried it but autowax seems like a great treatment for the graphite.

What's most important to me is the removal of salt residue from the guide assemblies where even the best rods are known to build a little superficial rust between the metal and the wraps / coatings.

I also take the time to remove any sand or particles that may have found their way into the reel seat or any other orifice.

I lightly sanded the cork before and that made it look pretty until the next time I slimed it. Decided that wasn't important.

TO tell the honest to goodness truth, the only time I ever "detailed" rods was when I was trying to sell them!

.02

Juro
Reply With Quote Quick reply to this message
  #4  
Old 11-16-2000, 08:26 PM
isoh isoh is offline
Senior Member
 
Join Date: Feb 2001
Posts: 119
RE:rod cleaning

All great tips!

What about cane rods? Anyone out there have a recommended cleaning regime?

<sorry, i'm a victim of my most current obsession >
Reply With Quote Quick reply to this message
  #5  
Old 02-24-2003, 07:10 PM
Smcdermott's Avatar
Smcdermott Smcdermott is offline
Jonesin...
 
Join Date: Mar 2002
Location: Rhode Island
Posts: 1,220
Superficial rust...

I took my rods out of the tube for the first time since November and noticed that a small bit of rust developed on the guides near the foot. I thought I gave them a good cleaning but apparently not good enough. Any tips on a remedy? Is it safe to use a little WD-40?

Sean
Reply With Quote Quick reply to this message
  #6  
Old 02-24-2003, 11:11 PM
striblue's Avatar
striblue striblue is offline
President of CAC
 
Join Date: Aug 2000
Location: Plymouth and Chatham, MA
Posts: 7,518
Don't forget to try a little rubbing alcohol on your cork grips and it will make them look like new... a little rubbing them down with a cotton ball or similar material is all you need.
Reply With Quote Quick reply to this message
  #7  
Old 02-25-2003, 12:44 AM
BobK BobK is offline
Registered User
 
Join Date: Dec 2002
Location: Lake Ontario Tribs
Posts: 871
Cane Rods

I learned care of cane rods as a kid. (I built 'em back then, too!)
That was before steelie fishing, and pre-fiberglass and graphite.
This will sound harsh, but here is what we would do.

Clean with mild soap and water, and quickly dry with a soft cloth. (spar varnish doesn't hold up to water too well.) Then closely inspect ALL wrappings (good cane gets LOTS of fancy wraps). Closely inspect the varnish for chips, cracks, etc., and check ferrules to make sure all is sound. Check all guides for telltale signs of wear. Cork is polished with baking soda moistened with water as a "polishing paste", and rinsed and quickly dried. If all is OK, then rod gets several coats of good paste wax (old Simonize
works well).

If anything is found out of order, then guides are removed, wraps are removed, and rod is sanded down and refinished. The tip guide is reversed and guides on the tip section will be rewrapped on the opposite flat to counter the "set" that all bamboo gets from use. You would use your own judgement on reversing midsections, if they needed it. You might also reset or replace ferrules, as needed. (In those days, every trout fisherman worth his salt had ferrule cement on hand - I still do, and it has a myriad of uses.)

Then you would carefully apply several thin coats of good spar varnish, drying thoroughly and rubbing down with rottenstone or pumice between coats, and finish with a couple of coats of paste wax. As far as waxing the ferrules during use, we just used to rub the male ferrules aside of our nose before using. It works well.

Today, this treatment sounds harsh, as we are more worried about "losing the manufacturer's markings". Heaven forbid! Well, sorry 'bout that, but in those days a fly rod was a tool for catching fish, and you maintained it in good working order - brand name or not!

BobK
__________________
BobK

Last edited by BobK; 02-25-2003 at 08:39 AM.
Reply With Quote Quick reply to this message
  #8  
Old 02-25-2003, 09:21 AM
John Desjardins John Desjardins is offline
Member
 
Join Date: Feb 2000
Location: Central MA
Posts: 1,839
Quote:
Don't forget to try a little rubbing alcohol on your cork grips and it will make them look like new... a little rubbing them down with a cotton ball or similar material is all you need.
Use caution on this. I have one grip that the alcohol is a solvent for the filler in the grip. Quite annoying to clean the grip and pull the filler out.
__________________
John Desjardins
Reply With Quote Quick reply to this message
  #9  
Old 02-27-2003, 08:37 PM
Tod D Tod D is offline
Here fishy fishy
 
Join Date: Jan 2000
Location: south shore MA, cape cod
Posts: 395
Attended a talk last night by Terry Tessein and he recommended using Olde English Lemon furniture wax on cork grips - after a soap & water clean up. Apparently conditions & seals the cork and protects against dirt, slime, etc...

Haven't tried it, but am intrigued.
Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
cleaning out the closet ncflyfisherman For Sale by Owner 0 05-25-2007 04:46 AM
Closet Cleaning Rod Sale Joe J For Sale by Owner 1 02-06-2007 05:09 PM
Cleaning a reel mojo716 Gear Talk - Fly Stuff Spoken Here 1 09-18-2006 07:41 AM
Reel Cleaning striblue Gear Talk - Fly Stuff Spoken Here 0 09-27-2000 04:56 PM


All times are GMT -5. The time now is 06:35 AM.



Copyright Flyfishingforum.com (All Rights Reserved)