I ordered two (2) handle kits that included winding checks, 3 spools of thread, reel seat, cork grip, epoxy, finish glue, and what I thought was a complete guide set. However, when I received the kits, there were no tip-tops included.
If you Look here you will see that the picture clearly shows a tip-top included in the kit.
I called Cabela's to complain and pointed out that the web site clearly showed a picture of the kit that included a tip-top. They first told me that the kit did NOT include the tip-top and that I would have to purchase them. After arguing with them on the phone and being on put on hold several times, they said the best they could do for me was to charge me the price of the tip-tops and give me free shipping. But I would have to 20 days to receive them. No thanks... I'll just run up to Bob Marriott's and get them from him.
I did the mail order thing for my 1st rod but now I would much rather deal with the local shops. The knowledge gained is well worth a little extra cost.
This is a very common mistake made by newcomers to rod building. Rod guide sets never include the tip tip. The reason for this is that the tips of rod blanks vary a lot from one rod maker or rod model to another. The guides, from stripping guides to running (snake) guides are of a pretty much standardized size progression for a given line wt rod; however, the same cannot be said of tip tops. I know of no rod building supplier who includes tips with guide sets.
And Cabela's catalog clearly states that guide sets do not include tip top, even though the tops are pictured with the guide sets.
good thing i saw this thread because i amgetting the materials i need for my first rod build is from cabelas
i was going to make a day trip to the one in my state
Over the years I have built perhaps 50 rods, including bamboo. I have done business with Cabela's ever since Herter's went out of business. I find them to be an excellent source of any outdoor equipment. I have built many rods with their components. I have broken a couple of rods that I built from their blanks. I sent them back to Cabelas, they replaced the blanks, and also sent me all the components at no additional charge. I am going to start on a new project of a two handed rod, all of the parts will becomming from Cabelas, excellent service everytime. Their catalogs always say when something is not included, youn just have to read. I can relate to buying local, but I am not going to drive 50 miles to buy locally. I wish they had a store in southern New England.
it is about a three hour drive to cabelas from where i live
but if there is little traffic i can make to the bass pro shops in gurneee mills IL in a half hour
It pays to order a tip from and at the same time as you order a blank, and specify "To fit above blank," because sometimes, the "5/64" tiptop won't fit your "5/64" blank's tip.
Manufacturing tolerances do sometimes deviate from their stated sizes. And a few times, I've suspected that the finish on the rod blank was too thick near the tip. That's easily dealt with, using emory paper or steel wool. Roughing the surface of the tip is a good idea anyway; makes for better glue adhesion.
Second post, first time here. Though at times I have my reservations, Cabelas Rocks! I busted the tip of a rod past the first guide. this was a POS starter rod but I liked the soft action! Three years after purchase I called and asked about getting it repaired. They asked I send it to them (Just the rod, not the tube etc.) and they would be in touch. Viola! a 10days after I shipped, I received a new rod complete with new rod tube and sock.
So as I say, for various reasons I occasionally have reservations. In sum,
they done good by me.
I hate those marketing tricks. One thing about mail order - no good advice comes with it. If you're lucky enough to have a local rod builder you might pay a few extra dollars but the advice is priceless.
I agree with chormer. I've had the great fortune to have the advice of a rod building great - "Smitty" of the Rod Builders Workshop (a Sponsor). He runs a well-stocked shop in Kingston, MA near Cape Cod just off the highway.
Not only has he built countless rods, but his wild "tales of adventure" are beyond fiction and knowing him they are all true. Stripers over 50 pounds, deer with unimaginable antlers, and a certain knack for "fair game" :hihi:
I highly recommend getting to know an individual, not a big catalog company if you want to build rods.
I hate those marketing tricks. One thing about mail order - no good advice comes with it. If you're lucky enough to have a local rod builder you might pay a few extra dollars but the advice is priceless.
If you go to the link he gave it is being updated. I bet when the update is complete you will see a picture WITHOUT the tip tops.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Fly Fishing Forum
163.8K posts
38.8K members
Since 2000
A forum community dedicated to fly fishing and sporting enthusiasts. Come join the discussion about safety, licenses, tips, tricks, rivers, reviews, accessories, classifieds, and more!