Bronzeback Angel - Fly Fishing Forum
>> Archive: Striper (etc) Flies Tricks of the trade

 
 
Thread Tools Search this Thread Rate Thread Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 03-17-2001, 10:05 AM
Bob Pink Bob Pink is offline
Active Member
 
Join Date: Jan 2000
Location: Massachusetts
Posts: 473
Bronzeback Angel




A color variation of the tradtional angel hair flies

Hook: Tiemco 600SP 2/0
Underbody: Clear Ultrahair or other stiff synthetic
Underbody: Pearl angel hair
Midwing: Copper flashabou or angel hair
Top wing: Olive Rainbow angel hair
Thread: Monofilament
Eyes: Molded epoxy (size to suit your preference)

Secure the untra hair to the hook shank about 3/8" behind the eye. You want the material to lay pretty flat and not flair out. Take a few loose wraps to down the shank to keep it under control (or dab on some softex or soft body)
Comb out some pearl angel hair to remove the tangles, tie in your first bunch under the shank so that you have length divided 2/3 - 1/3 to create a tapered body.
Tie another bunch of pearl tied to the top of the shank to make sure the untrahair is covered on each side. Add one more buch of pearl to the top (optional) if you feel the body needs more bulk.
Add the copper mid wing
Add the topwing of brown/olive rainbow angel hair.
Whip finish the head.
Apply epoxy eyes to the sides of the head JUST behind the eyes. (usually the self-adhesive backing will hold them in place.)
Mix your 5 minute epoxy, heat the tubes in hot water for 5 minutes before mixing to make if flow easier (will shorten the working time so don't mix a big batch)
Using a bodkin, gather enough mixed epoxy to fill the gap between the two moled eyes on the bottom of the shank, hold the fly upside down and drop the epoxy in the gap, beter to use too little and add more than too much and have it all over the place.
Right the fly and apply epoxy to the gap above the shank.
A properly epoxied head will have the epoxy slightly above and below the eyes but not covering the outer surfaces.
Rotate by hand or on a dryer to distribute the epoxy evenly until set.

Bob Pink
Reply With Quote
 

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bronzeback Clave juro Warmwater flyfishing 6 04-24-2002 01:54 PM
Bronzeback Clave juro Warmwater flyfishing 11 07-12-2001 07:42 AM
Bronzeback Sidenote! Lefty Warmwater flyfishing 2 08-04-2000 10:03 PM
Bronzeback Clave Nathan Smith Warmwater flyfishing 4 06-03-2000 10:11 PM
Bronzeback Clave juro Warmwater flyfishing 2 01-31-2000 12:01 AM


All times are GMT -5. The time now is 07:21 PM.



Copyright Flyfishingforum.com (All Rights Reserved)