Fly Fishing Forum

Fly Fishing Forum (
-   >> Archive: Striper (etc) Flies (
-   -   Pollock Patterns (

Lefty 02-25-2000 09:07 PM

Pollock Patterns
[img]" border="0">

<img src="[/img]

Been working on Pollock for the rock wash, for Nahant, Rockport, Gloucester. Top one used long Polar Fiber and
brown hackle. Bottom guy uses short polar fiber for belly and greens and greys of bucktail.

Bob Pink 02-27-2000 06:55 PM

RE:Pollock Patterns
Nice going on the pollack ideas. I experimented with some this weekend using a flatwing body with yak hair and a traditional tapered head and then a similar body with an olive dear hair head. Overall length about 6 - 7". I'll try to scan an image soon to post.


Lefty 03-07-2000 01:38 PM

RE:Pollock Patterns
Yo Bob,
Can we see some of yours? I tied a couple more pollock last night. Would love to see yours. Can't wait to toss some into the rocks at Nahant.


Bob Pink 03-07-2000 10:17 PM

RE:Pollock Patterns
Sorry Terry, I forgot all about getting an image scanned and uploaded. Will try to have one ready tomorrow night. Yours really look good........

Bob Pink 03-09-2000 07:12 PM

RE:Pollock Patterns

Ok gang, here are two versions of a pollack pattern I've been playing with. Both are built on the similar formula.

The smaller version uses a short-shank hook, this was tied on a 2/0.
Small pinch of white bucktail just above the hook point.
Yellow bucktail tied in above the hook point and rolled around the shank.
Olive bucktail tied in front of the yellow.
Add one or two olive hackles to the top of the shank using the bucktail as a base.
Pinch of yellow bucktail tied in front of the hackle.
Olive krystal flash (I'll use 4 strands)
Olive Yack hair as long as the hackle (taper the ends)
5-6 peacock herls
Taper, whip finsh and glue
This should leave you a good 3/8 - 1/2 of exposed shank behind the eye.

Take a pencil thick bucch of deer body hair, tips pointed towards the back, lay it on top of the tied off head of the body, make two loose wraps with most of the hair pointing towards the rear (don't tie in the center of the bunch) and pull tight flaring the hair out. Make two more wraps weaving the thread along the original centerline. Then keep adding bunches to the sides using the same method (might take 4) until you have the hair neatly flared back along the body.
Next add bunches of hair the the exposed shank up to the eye. You may need to alternate between spinning hair on the shank and then 'stacking' hair in the thin spots.

A neat trick for tying off the thread is to make a few wraps while pulling the hair backwards towards the body, take a good drop of zap-a-gap and wet the threads, then qickly make another 6 wraps. The glue locks the threads up nicely. (I't tough whip-finishing a head with all that hair flaring frontwards.

Trim the head to a neat taper, leaving those tips that you nicely arranged around the body. Add eyes with 'Goop' and you are done.

The larger version I put on a long shank hook
I used three hackles stacked, a long dark yellow, a grizzley, and an olive.
I kept the top wing (yak hair) very sparse, maybe too sparse on this example.
Then added two olive marabou plumes tied in praying hands style before building the head.
(Now that I look at it some peacock herls would have been nice too!)

The large one comes out to over 7" long but most of the weight is in the head. I think it will cast OK as long as I slow down and don't try to force it out there....

Suggestions from the group?

All times are GMT -5. The time now is 12:57 AM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright (All Rights Reserved)