Fly Fishing Forum - Reply to Topic
>> Archive: Striper (etc) Flies Tricks of the trade

Thread: YASE (Yet Another Sand Eel) Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
03-21-2000 08:14 AM
StriperTom
RE:YASE (Yet Another Sand Eel)

By the way, Juro made some interesting comments on the coloration which I hadn't considered before.. mainly the difference in color between open water sandeels and estuary ones. Seeing as 90% of my fishing is the latter, I will be trying some rootbeer/tan versions

-- Tom
03-21-2000 08:11 AM
StriperTom
RE:YASE (Yet Another Sand Eel)

Ok, here is how I tied up the fly.. Actually here is how I would tie the next one, which is more important I'm sure this fly would work with any of the standard materials, but I had just picked up several different types of Angel Hair and was eager to use it.

Body: Holographic tape
Tail: White Angel Hair or Bucktail
Flash: Silver Angel Hair or Pearl Sparkleflash
Wing: Green Angel Hair or Bucktail

With the first fly, I put the body on first, and then tied in materials around it. The next time I try this fly, I will try tying in the materials as follows:

1 - Take a small bunch of white wing material and tie in on the bottom of the hook shank. You want to extend the wing material about 2-3 hook lengths beyond the bend, depending on the type of baitfish you are trying to imitate. Use a little longer wing then what you want in the finished fly, as you will trim it down in the last step.

2 - Take another small bunch of white wing material and tie in on top of the hook.

3 - Take flash material and tie in on top of white.

4 - With the backing tape still on, take a piece of holographic tape and fold it in half, roughly the size of the body you want to create. Trace or just cut out the outline of the body cavity you want to create, small and narrow for sand eels, or a little wider for silversides, etc. Try to keep the shape streamlined so that the top wing material will flow over it smoothly and not just go around it.

5 - With the backing still on the tape, test fit the body to see how it fits and looks, making sure to leave plenty of room around the gape of the hook and at the eye.

6 - When you have trimmed it to the right shape, peel off the backing and fold it over the white wing and flash material you tied in earlier. Try to keep the wing material evenly distributed coming out the back of the tape when you fold it over. Depending on the tape, it may or may not stick well enough to stay in place. If not, apply a few drops of zap a gap or any other super glue to get it to hold.

7 - Depending on the profile you want, tie in additional bunches of white winging material at the eye of the hook, over the body, and then finish with the dark wing material over the top.

8 - At this point I decided to apply Loon Hard Head (like Softex) to the body of the fly and the top wing material to tack everything into place. I also applied the eye in this step and used the Hard Head to hold it.

9 - Once that dried, I applied a thin coat of 5 min epoxy to seal the head and body of the fly.

10 - If needed, trim the wing material to form the correct profile. Make sure that you make lots of little cuts and work gradually from the front of the fly to the rear. Make sure that the ends of the wing material dont all line up like a paintbrush.. this is very un-natural looking.


I think it took longer to write these instructions then to tie it

If you guys tie some up like this, make sure to post a picture if you can..

-- Tom
03-21-2000 05:41 AM
Pete
RE:YASE (Yet Another Sand Eel)

ST,

Nice job, and good name ! What did you use to coat the body with - is it silicone or plumbers goop? The eye really stands out and it has a nice profile.

Looking forward to the instructions,

Pete
03-21-2000 04:37 AM
doug
RE:YASE (Yet Another Sand Eel)

Nice job, Tom. Looks like a fish getter! Recipe? Hint, hint.
03-20-2000 11:50 PM
juro
RE:YASE (Yet Another Sand Eel)

Definitely a fish getter - and the rigid body prevents fouling. The color choice is great for open water coloration too. I tie a similar fly and use rootbeer or lighter tan for estuary versions of same. Easy to cast too, and very effective on all gamefish who eat 'dem sand eels.

How did you form the body?

nice work!
Juro
03-20-2000 10:18 PM
StriperTom
YASE (Yet Another Sand Eel)

Here is yet another sand eel pattern.. I came up with this one while playing around with some new materials.

It doesn't show up too well in the picture (got to learn how to use this thing) but the back is a nice dark green with a lot of flash.

[img]http://people.ne.mediaone.net/tsheehy/images/sandeel1.jpg" border="0">

<img src="http://people.ne.mediaone.net/tsheehy/images/sandeel2.jpg[/img]

Comments?

-- Tom

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:56 PM.



Copyright Flyfishingforum.com (All Rights Reserved)