Fly Fishing Forum - Reply to Topic
>> Archive: Salmon & Steelhead Flies Spey flies to mixed wings, new innovations

Thread: intruders? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
12-18-2003 05:19 PM
SDHflyfisher thanks that helps alot
12-18-2003 05:11 PM
KerryS The Intruder:

By Ed Ward

Hook:
The fly itself is tied on a size 2/0 Mustad 36890 salmon that has been straightened out and cut off. The trailer hook is a Daichii 2451—size 2 for steelhead that average under eight pounds, size 1 for those that run eight to 16 pounds. Sand smooth the part of the hook shank you have cut.

Ribbing:
Tie in a loop of 25-pound-test monofilament a quarter-inch up from the end of the shank. Tie in oval gold tinsel and take two wraps in back of the mono loop, one wrap in front.

Rear Hackle:
Tie in a long, soft, black hackle and take three wraps.

Feelers:
Tie in nine strands of dyed-orange ostrich plume, on each side of hook shank. Tie in dyed-orange ringneck pheasant tail and take three of four turns.

Body:
Tie in a long, skinny badger hackle and leave hanging. Tie in burnt-orange chenille and wrap forward tightly to within a half-inch of eye of the hook. Wind the badger hackle forward through chenille, ending with three successive turns at thee point where the chenille terminates. Spin a small clump of black deer hair and trim butts flush with the shank. Tie in orange ringneck pheasant tail and take three or four turns.

Shell:
Tie in two cree hackles on each side of the shank for “wings”. Tie in dyed-orange winea hackle and take four or five turns.

Head:
Tie in a small ball of black chenille. Tie in lead eyes. Whip finish. Cover head with Aquaseal thinned with Cotol.

Tying Note 1:
Ringneck pheasant tails are split down the stem with a single-edge razor, do they can be wrapped as a hackle. Soaking the tail for 10 minutes in warm water can aid in the splitting-and-wrapping process.

Tying Note 2:
Other species of pheasant produce differing appearances; Amherst is particularly striking.

Rigging the Intruder:
Pass your leader through the eye of the hook, then through the monofilament loop, then through a quarter-inch-long piece of 16-gauge electrical wire from which the wire core has been removed. Tie the leader to the trailer hook with Lefty Kreh’s nonslip loop knot. Push the electrical insulation up onto the end of the hook shank and pull slowly on the leader to draw the knot snugly into the other end of the insulation, making sure that everything pulls together with the hook point riding up.

Ed prefers to tie the Intruder on straightened Mustad hook shanks. He shared with us that, for the innovative anadromous tier, the pattern can also be tied on tubes or Waddington shanks; this would eliminate the need for his clever monofilament loop, which you’ll learn about in this edition of Inside The Ultimate Fly Box. One more thought Ed asked us to share with you: Please do not tie the Intruder on single hooks larger than size 1/0. Single hooks larger than this, he reminds us can be harmful to wild steelhead, every one of which should be released alive and unharmed.
12-18-2003 04:46 PM
SDHflyfisher
intruders?

what materials are used to tie intruders

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:01 PM.



Copyright Flyfishingforum.com (All Rights Reserved)