Fly Fishing Forum - Reply to Topic
>> Archive: Salmon & Steelhead Flies Spey flies to mixed wings, new innovations

Thread: The turbo spinning block for dubbing Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
12-31-2003 05:16 PM
speydoc Thanks for the comments guys - ever since I got my didgital camera I have been looking for an excuse to play with it, this post did just that - exellent post, Matt. In terms of what one can do with "dubbing" brushes the only limit is one's imagination.
Metalhead, careful - I have been looking for an excuse to head up north! - did you get that parcel yet?
speydoc
12-31-2003 01:14 AM
mattzoid Speydoc,

Thank you for you time and effort. Great work.

Matt Burke
12-31-2003 01:03 AM
metalhead
cool hackling!!!

speydoc, great hackle job!!do you make house calls??
12-31-2003 12:41 AM
MJC
Hey Speydoc...

NICE informative pictures and great looking hackles. Thank you for taking the time to post them. Take care, MJC
12-31-2003 12:27 AM
speydoc For comparison I have a shot with the spun hackle in the rear, next is split Amherst centre tail(very time consuming), followed by stripped Golden pheasant side tail & stripped Amherst side tail - stripping is the simplest and fastest way to produce a hackle from these thick stemmed feathers - unfortunately not all feathers strip well, the Amherst centre tails are the most difficult which is why I produce a spun hackle from them as they are amongst the prettiest feathers to use.Of course one can always use the centre tails just as a beard - this is certainly the fastest & simplest way to use them, but not necisarily the most fun!
The "machine" is simply a small electrical engine with a hook attached - the one in the photos was obtained from a fly shop in Kamloops - one can make some thing similar from a small handhelled fan(obtained from any of the "dollar stores" in the summer in Canada) by removing the fan and replacing with a hook - I would also remove one of the two batteries and replace it with a nail, cut to size, to slow the engine down.
speydoc
12-31-2003 12:04 AM
speydoc Final step - folding the hackle flat
12-31-2003 12:02 AM
speydoc Correction to the last photo - this is the hackle end on to show the bottle brush efect that is present before one folds the hackle to get a flat workeable hackle. The attached photo is the one on trimming the but ends
12-30-2003 11:56 PM
speydoc Shot eight - trimming the butt ends to neaten up the hackle
12-30-2003 11:54 PM
speydoc Shot seven - close up on the hackle with a needle being used to pick out a fibre before it binds up
12-30-2003 11:51 PM
speydoc Shot six - wide angle as the hackle is spinning
12-30-2003 11:49 PM
speydoc Shot five - close up on the hackle as it starts to spin, if the fibres start to bind up - stop spinning and pick them out before restarting the machine - allways keep firm tention on the wire
12-30-2003 11:43 PM
speydoc Fourth shot - I clamp and cut the dubbing wire so I can lift the entire hackle up of the board as I start spinning it
12-30-2003 11:36 PM
speydoc Third shot - close up of Amherst after cutting
12-30-2003 11:34 PM
speydoc Second shot
12-27-2003 10:42 PM
speydoc I am having trouble with posting and wiil try another time
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:33 PM.



Copyright Flyfishingforum.com (All Rights Reserved)