Fly Fishing Forum - Reply to Topic
the Rod Rack Rod Builder's Forum

Thread: tag ends of guide wrapping Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
08-16-2003 07:26 PM
daveg L. A. Garcia's book is very clear how to pull the thread under the wrap and breaking it off below the windings. He builds a thread pulling wire loop using guitar string, a piece of dowel and epoxy. His book is very good with nice pictures.
08-12-2003 01:53 PM
Tom H. The best and cleanest method I've found (Courtesy of L.A Garcia's video) is to use a bobbin threader instead of a piece of heavier thread.

Leave your tag end long enough to get a hold of and pull it and the bobbin in opposite directions.

The tag end will be left under the over wraps every time.
03-11-2003 11:23 PM
saltRon
Tag ends

Hi guys

Have not been arround for quite a long time.

The best way to burry any tag end on the over rap is to pull the tag at 90 degrees to your wrap in point ,it builds a little tent snip as tight AS YOU CAN GET TO the tent ,, the tent will cover the cut portion almost compleyely. A little singe will eliminate any hairs and just massage the remaining wraps to cover the cut portion.

saltRon <*}}}}><
03-10-2003 03:41 AM
Nooksack Mac Another way to deal with that "stubble" left when your closest trim with razor or scissors isn't quite close enough: burn it. First separate the stub into fuzz with scissors, bodkin or needle. Turn it to the bottom of the rod. Quickly (less than two seconds) flame it with match or lighter. If you take a second too long, you'll smoke and/or burn through the thread. But done properly, the fuzzy stub will disappear.
03-09-2003 05:45 AM
Eric Golden
Tag ends on guide wraps

Thanks for your replies. Cutting the tag end before pulling it through Is such an elegent solution. Now why didn't I think of that. Flyfisha1 I don't want to hear you complaining about the winter while you are comfortably ensconsed in Florida. Have some mercy on us poor fools who are slogging it out in New York.
Jim W. thanks for the photo. It helped.
03-08-2003 07:28 AM
JimW I'll second flyfisha1's repsponse. Check out the pic below. If you pull the loop part way through then cut the tag end before pulling the loop all the way through the tag will be buried under the wraps. Try to get the tag at least 3/4 of the way under the wrap.

Use the same size thread for creating the loop under your wrap. I only used that yellow backing to show contrast. A thick material like the 30lb backing can leave you with a loose wrap.
03-08-2003 06:10 AM
flyfisha1 There's a way to do it without having to cut near the wraps: simply cover the looped piece of thread used to pull the tag end of the wrapping thread under the wraps with some room to spare, then pull the loop out from beneath the wraps when you're ready, and there will be no tag end left to cut (it's completely beneath the wraps). Good luck!
03-07-2003 09:34 PM
John Desjardins Good question. I've run into the same problem and have ended up triming the nub after the 1'st coating with epoxy. Theres got to be a better way.
03-07-2003 09:10 PM
Eric Golden
tag ends of guide wrapping

I have a question. When I tie off a guide wrapping I am not always able to cut the tag end as close as needed, at that point the tag end is too short to grab in order to get the razor blade in there to cut it right against the wrapping. Is there any suggestions for dealing with these recalcitrant threads (no pun intended).
signed
At loose ends

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:17 PM.



Copyright Flyfishingforum.com (All Rights Reserved)