Fly Fishing Forum - Reply to Topic
the Rod Rack Rod Builder's Forum

Thread: Effective thread finishing technique for rod guides Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
04-03-2002 03:10 PM
bellacoola Instead of using a bobbin threader, or mono, or winding thread, I like to use those dental floss holders that have a preformed loop. I am not exactly sure, but I think they are made of nylon. They are strong, have a small diameter, and are convenient to use.
03-22-2002 03:30 AM
Domenic I agree with Saltron.Check out :
http://www.flyshop.com/centers/rodbuilding/
There are some informative videos on the subject here. I use rod winding thread for my loops.
03-21-2002 08:18 PM
saltRon
Finishing Wraps

Different Strokes For Different Folks

You are all on a similar track with the loop under the final wraps but keep in mind that the larger Diameter looping material
will also take up additional space against the blank and will relax the final tension that you applied in those final wraps.

If you are applying an inlaid turn in contrasting colour or a thread trim ring you will find that the thin thread as in rod [loop]winding material will allow you to develop a tighter wrap. You then pull the tag ends at 90 D. to the blank which creates a tent over the wrap,, cut close to the tent,,, tent snaps shut and burries the tag ends

My .02 saltRon
03-21-2002 04:10 PM
Nooksack Mac Here's how I complete (pull through) winding wraps. It seems so simple and obvious that I'm surprised that this little technique isn't universal: Just make several loops of light (say, 3X-6X, or 3-6 lb.) monofilament, or rod-winding thread.
Cut off a 6-7-inch length; tie the two ends together. You now have several little ovals. Tie an inch or so of bright yarn to them at the knot, so that you can easily find them on your bench. Make several, because they do eventually break at the apex.
Normally, six wraps over the mono loop seems to produce optimum tension. I usually cut off the thread close after pulling it through, but here's how to do it more neatly, hiding the thread end: Put the thread end into the mono loop and pull it against the end of the winding, tight enough to hold the thread for a moment. Then cut the loose thread end about 1/16" to 1/8" from the mono loop; pull the mono loop through.
03-20-2002 06:51 PM
JimW Nice tip. Are you referring to one of the renzetti style threaders Nylon loop? I would be careful of using any metal wire directly against the blank. I'd be afraid of puting a scratch in it that may cause a crack down the road.
03-06-2002 12:50 PM
Tod D
Effective thread finishing technique for rod guides

I've been augmenting my rod building 'tutoring' from Smitty with L.A. Garcia's book "Handcrafting a Graphite Fly Rod" ($14 at the Marlboro Show from Angler's Art!). Found a tip in Garcia's book to be particularly effective: he uses a bobbin threader (BT) to finish his guide wraps (by pulling the tag end of the thread back under the preceding wraps).

I suspect I won't explain it well here, but you start by wrapping over your BT about 7-8 wraps from the end. When you've completed your wraps, cut a 7'8" tag end of thread. Maintain pressure on the wraps & thread the tag through the BT. While keeping constant pressure on the tag end, you then pull the BT back under the wraps.

Once the BT tip is under the wraps, you then apply equal pressure to the thread tag end and the BT. The thread eventually "ruptures" under the wraps and I've found it to leave a nearly seamless finish.

Hope this isn't entirely unintelligible. For those NE folks, suspect the book may be found at this weekend's show in Wilmington.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:05 AM.



Copyright Flyfishingforum.com (All Rights Reserved)