|01-17-2002 11:40 PM|
not sure if you've done the cutting yet, but the cut point can be determined by the weight of tips you expect to use. FIguring that the floater portion will easily turnover tips of equivalent or lesser weight, I just cut at the equivalent diameter of a floater. For example, when desiring to toss 8 weight tips on a tapered floating line, I'll cut the floater at a diameter equivalent to a floater 8 weight. THis provides enough ooomph to turn over the 8 weight tips.
|01-15-2002 05:04 PM|
My God! An honest Dentist? "This is not going to hurt a bit."
Wow, Malcom you dropped the ball on this one. "Your" fish could have been any size, type, light tippets, etc. and you 'opt' for honesty.
We must speak... in private .... this is a fly fishing board .... there are certain expectations... even better if they can't be verified. :hehe:
|01-15-2002 04:41 PM|
First fish on the Tay! Spring is not far away.
Thanks for the great news Malcom, I hope someday I will see opening day in person.
|01-15-2002 04:30 PM|
Sorry to disappoint
Hi Fred et al.
Having read my thread again I see what you mean. What I meant to say was someone caught a fish on the opening day on the Tay. Lucky B gger I was busy working I do not get lunch hours? like yours Fred.
|01-15-2002 03:53 PM|
First fish! Details! Details!!!
Ok Malcom "spill your guts!." We want details on type, size, etc.
|01-15-2002 03:06 PM|
I've been using these for a couple of seasons now but I don't think they get down enough. Also the river flow is quicker at the top so a long floater tends to come round quicker. This is on of the reasons I fish a full sinker, but I am willing to try one of your long sink tips to see how it compares with an intermediate.
PS 1st fish from the Tay today opening day.
|01-15-2002 06:34 AM|
Similar stuff to Kush
I also use the super fast sinking short leaders fro Airflo off the end of a 7-8 midspay. Sinks like a rock and very quick to pop back to the surface for your next cast.
Think the short nature of these things (like 4' long) precludes having to do the surface roll cast frequently necessary with a 15 foot heavy tip.
|01-15-2002 01:05 AM|
If you haven't already taken the drastic step on the chopping block, there is an alternative that leaves your line intact. Over the past two seasons Dana and I have been experimenting with "poly-leaders" made by Loop and Airflo (and a number others just recently on the market). These are mono core leaders covered with tungsten to provide the weight, they come looped and I think they are the cat's ass! I attached a heavy butt section to my fly line and tie a loop 3-4" down, to which I loop the poly-leader and add a 4' section of tippet. Now the regular front taper turns over even the poly-leader and it sinks like mad due to its thin profile. They come in every sink rate from Hover to type VI. I can hit bottom in any water I would normally expect to catch a steelhead in with standard tips and the true bonus it is casts like a regular floater, but gets down like a tip! We have not used the standard sink tip since we started experimenting. These are very cool.
|01-09-2002 05:03 PM|
Thank you chaps,
I had changed price to US dollars to make life easy.
We work £ sterling as we are outside euro land.
I was just intending making the tips as in part one of the article, part two looks to complicated and I think I would be better with a cheap line.
Must check new sites , thanks again
|01-09-2002 04:38 PM|
Willie Gunn-Line Chopper
Willie, Sprocket has a very good point. The article Fred was referring to is here:http://globalflyfisher.com/fishbetter/juro.htm
On Mark Bachmann's website under Mastery spey he says to cut the line where the diameter is .070:
There is more good info here:
|01-09-2002 04:03 PM|
Willie - if you new line cost $80 (or pounds or euros or monopoly)
I would suggest you leave it intact and cut up an older one, maybe even an old trout line and use it for the running line.
Just a thought.
|01-09-2002 02:57 PM|
t/t triagular taper should have known
|01-09-2002 02:36 PM|
Juro, please jump in here please.
Doc, Juro has an excellent web site on making up sink tip lines; don't have it as a 'fav. place' on office computer but he should be able to connect you asap.
It's Juro's directions I've followed for years on the how-to of this.
|01-09-2002 02:30 PM|
|fisshman26||wulf triangle taper =t/t You would do the same for a wf or dt just match up the diams. but the heavier of a tip that you want, the more you must cut off of the taper of the sa line. But by leaving some of the taper you will have a smoother casting line and the triangle taper would enhance that even further.|
|01-09-2002 02:25 PM|
another term please ?
|This thread has more than 15 replies. Click here to review the whole thread.|