Fly Fishing Forum - Reply to Topic
the Rod Rack Rod Builder's Forum

Thread: High Quality Fly Rod Components? Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Home Waters
Your home waters
Current Favorite Fly
If you only had one... (change anytime)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-06-2008 11:51 PM
blindcurvw Thanks for the feedback and original inspiration...

I'm a tough self critic (Being an engineer is a curse) and not very happy w/ finish on wraps. Base layer of flexcoat was applied too cold which allowed many wraps to set w/ a ripple (barely noticeable in this pic), a two or three bubbles. I know better but was forced into the basement during this step due to poor planning. Additional coats helped smooth almost all variation out.

I was wondering about wrapping the female ferrule and thought hard and decided a little bit would go a long way... Now you got me concerned.

Easy enough to strip/re-wrap/finish 2nd section, third section wrapped fully don't need to do anything there, tip section is fully epoxied over decorative wrap. Not much I can think to do on tip section, hope the epoxy finish helps.

Took it for a test drive Sunday evening but Pike weren't cooperating. No problem as I was perfectly content to just cast... Wow, impressive how easy it is to make some booming casts w/ that rod. Will try to get some action on it again Thursday.
05-06-2008 05:20 PM
Warren Looks like the wraps & finish came out pretty well Blind. One word of caution though, I would make my female ferrule wraps at least 3/4 inch long on any future rods. I have seen some discussion that they are really unnecessary on on SOME blanks, but the consensus among those I have discussed it with suggest that they are indeed a must. I tend to agree. I like your tip section wrap over the gray. Well done

Looks like you have a winner. now go catch some fish
05-05-2008 11:11 PM
blindcurvw Rod 1 of 2 Complete... Components in transit for Rod #2

TFO TiCrx 9' 9WT
ALPS Triangle Reel Seat Tich/LtGold
Guides: 2 Stripper + 7 SF + Tip - All Tich framed w/ Blue Zirconia inserts
Handle: Custom Two-Tone Full Wells style w/ Fighting Butt
Wrappings: Three Tone Royal Blue & Silver HT Metallic guarding Royal Blue NCP
Finish: Flex Coat (2x) + Permagloss (3x)

04-19-2008 11:13 PM
blindcurvw Now building two rods....

Sage Xi2 8WT w/ ALPS and guides (TBD)
TFO TiCrX 9WT w/ ALPS and Single Foot TiCH-Blue Guides

Glued and turned the handle for the TFO, here's pic w/ reelseat and handle together.

Small flat spot in taper near top of handle I want to blend out a bit more... Otherwise , I like how it came out.
04-13-2008 08:47 PM
Warren Blind,
Now we are cookin' Looks good to me. The good thing about custom rods is..... well....they are custom. What you want is what is you get.

Remember the curse of the craftsman is being in a hurry.

If it takes you all year to finish up, no worries mate!

When you get to the next step send another pic.

BTW, The drill press can be the prime mover for all the steps needed to turn rod components even a reel seat if you think it through
04-12-2008 07:49 PM
blindcurvw Getting a slow start as I've been struggling with components and experimenting w/ new techniques. This rod is a gift so am going to put in my very best.

Used my drill press as a lathe and made my first custom fighting butt. I'm pretty thrilled w/ how it turned out. This is just a proto and will now get some nicer cork to work with on the final version.

I'm really impressed with how well the drill press works!!!

04-02-2008 09:40 PM
blindcurvw We'll see if my end product is as photo worthy. Will do my best.
04-02-2008 07:53 PM
Frogfish Very Nice!
04-02-2008 04:06 PM
Warren Thanks guys, I appreciate the the kind words. Blind you will have to show us what you come up with when you are done.

Remember the rule.....If you did not take pics, it did not happen
04-02-2008 02:43 PM
blindcurvw Kudos on the rod and the photography (nice pics).
04-02-2008 04:57 AM
FishHawk Great looking thread work , Warren. FishHawk
04-01-2008 09:07 PM
Jim Miller Warren
Super job on the rod build!
A very nice custom job all around.

I'm waiting for TFO to make their Bluewater blanks available. I'd like to spin up a homegrown 16 wt.
04-01-2008 07:59 PM
Warren Blind, I think you will like the ALPS . There are not to many out there right now you will have something different. I know for a fact that it will spruce up a Sage Xi-2 real nice

As promised I said I would post up the the TFO 9 wt when I was done.

Santosh above I said I used Cobalt Blue thread. I lied! I actually used Royal Blue. There is a difference

03-31-2008 12:28 PM
blindcurvw Warren,

Thanks again for feedback. I've ordered the ALPS AH12M reelseat and hope to get it in a couple days so I can get started on this rod this weekend. Season is coming fast!
03-09-2008 06:48 PM
Frogfish Looking forward to the pics! Yea, I love the look of blue on blue or blue on black with metallics!.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 12:24 PM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright (All Rights Reserved)