Fly Fishing Forum - Reply to Topic
>> Archive: Striper (etc) Flies Tricks of the trade

Thread: drying motor Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-11-2005 02:38 PM
Limpe Back here people use the motors from a micro-wave oven.

Best feature of some of them is that when power is switched off the motor turns the other way, they are powerfull enough to rotate a chicken and do a great job doing it slow...

Most of these motors work on 220 Volts (current over here) and i guess that in the US the motors work on 110 Volts, so no need to reduce the current or to make use of current regulators. Easy wiring, just a piece of cord, a switch a box to house the motor and a piece of faom to press your hooks in...

Good luck.

Limpe
02-10-2005 10:03 PM
Tod D Broadbill and Jim nailed it! Thanks guys. I totally forgot about the disco-ball! I've got a left over motor and plenty of glitter (for epoxy). All I need now is a big foam ball and I'm in business...
02-10-2005 05:48 PM
porkslice
thanks

Thanks for all the help guys, appreciate it.
02-10-2005 11:53 AM
Broadbill What Jim Whalen and Tod said: U-Do-It Electronics just off Rte. 128 in Needham. I found (if memory serves) a 5-rpm AC motor intended to rotate a silver disco ball. Extended the armature, put a foam wheel on it and bolted it onto a scrapwood L-shaped base. Six or seven bucks and an hour of workshop time.
02-10-2005 11:37 AM
Eddie I should have posted here
02-10-2005 11:22 AM
Tod D I've built a couple of drying wheels/set ups using small clock motors. Cannot recall the rpm's, but they didn't cost more than a few bucks each. I got mine at an electric supply co in Needham/Newton Highlands - just off 128. Cannot remember the name, so I'm no help on that.

FWIW, I rewired the motor so that the cord had an on/off switch, built an oak stand, attached a piece of small diameter alum tubing to the motor shaft, got a big foam disc from Michael's... and there you go. Motor's been powerful enough to turn rods too. All in, probbably cost less than $10 - and I seem to recall the motor was around $6.
02-10-2005 11:20 AM
JimW U do it electronics should be able to hook you up.
02-10-2005 08:36 AM
Adrian One of the booths at the shows was doing a cheap battery driven job a couple of years ago. The motor was from a rotating Christmas Tree decoration.
02-10-2005 08:22 AM
StriperTom There are quite a few motors (both AC and DC) available online from Jameco.

http://www.jameco.com

Do a search for the following keyword "motor,gear,120vac"

Here is a link to the catalog page for probably the best bet for an epoxy drying motor, its the one in the upper right hand corner of the page:

http://www.jameco.com/Jameco/catalogs/c251/P116.pdf


-- Tom
02-10-2005 07:46 AM
Eddie I spent a little time looking and couldn't find any think. Rotiserie motors are supposed to be good, but new they are not that cheap. I gave up and bought my self a nice one. Time save has to be worth some thing. I'm sure that another board member will have better advice.
02-09-2005 11:01 PM
porkslice
drying motor

Does any one know where I can find a cheep 7 rpm electric motor for a
rotory epoxy dryier? I have been serching for some time know with no luck.
Thank you for any help.
Porkslice

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:22 AM.



Copyright Flyfishingforum.com (All Rights Reserved)