Fly Fishing Forum - Reply to Topic
>> Archive: Salmon & Steelhead Flies Spey flies to mixed wings, new innovations

Thread: Tying Tube Flies Question: Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Home Waters
Your home waters
Current Favorite Fly
If you only had one... (change anytime)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
09-07-2004 02:59 PM
Gary W Touching again on the blind eye salmon hook method, a method i used to use was to take any large single salmon hook and bend it. What you do is heat it and staighten out or snip the eye. Heat it again and bend it so that you have small bumps along the plain of the hook that increase in size as you get towards the bend. When you have achieved this, heat the whole hook and drop immediately into hot water to temper the metal.

It's a bit of a pain to do but works very well. It's a method that I used to use that I forgot all about until this thread. I may start employing this method again as, it is very effective at holding the tube securely.

Also, a lot cheaper than the mandrels and special tools.

Hope this helps somebody.

Tight lines,
09-07-2004 11:11 AM
small finishing nail with a threa wrap

Why spend money on a mandrel when you can use a small finishing nail of approximately the correct inside diameter of the tube, use thread to wrap it for the EXACT inside diameter of the tube(or the thickness required to make a tight inside fitso the tube does not spin , and you have a perfect mandrel that will hold tubes tightly and firmly...just insert the hammer end on the nail in the vise and lock her down. Pus h the tube on the pointed nail end until it is firm and you are good to go.I have tied a ton of tubes in the last month in anticipation of a trip, and this device has worked perfectly for me....2 cents.
09-07-2004 01:53 AM
knutalf You could also try to use a blind eye salmon hook as a tube holder, the gradually increasing diameter usually holds the tube securely. Sometimes when using brass or aliminium I have found that the tube material rotates on the inner tube, but super glue fixes this. Other alternatives to the commercial tube tools are needles of variaous kinds. Even if I have a tube vise I seldom use it since I find the simple hook or needle system works better.

09-06-2004 09:09 AM
1 More Cast Thank you for the input!! I will try all of the above recomendations till my HMH manderals arrive.
09-05-2004 04:52 PM
Gary W One of the easiest ways that I have found to eliminate this, assuming I am working with a similar tool, is to slide the tube on to the mandrel/pin, followed by a piece of silicon tubing, push into the tool tightly and tigten the screw. The compressed silicon tubing should be enough to hold the tube steady.

Hope this helps.

09-05-2004 12:35 PM
Another suggestion...

A rotating tube is a real pain in the keester!
The HMH mandrels sport a slight flange at the end of their quite rigid tying shaft...
The tube slides up the mandrel shaft and then fits snugly over the widening flange and free spooling is essentially eliminated...
If your mandrels don't have that flange, make one yourself...
Wrap some flat waxed nylon thread to build up a flange (about a 3/16' widening taper) and secure it with a smear of super glue...give it a chance to fully cure.
Slide on your working tube over the "enhanced" shaft...if the build up is sufficient, it should hold the tube fast!
That's what I did before I got the HMH tool...cheaper versions have not-so-rigid flangeless mandrels...junque!
Do it right the first time and you only have to do it once!

Also, while you're tying...
No need to wrap too tightly with the thread...
Too tight and the tube will be compressed and removing it (off the mandrel) will be a problem...
A dab of head cement, as you tye, will ensure that the material will stay put, and make for a much more durable fly!
A little practice goes a long way!
09-05-2004 11:34 AM
Tayside I use the same device, loop a rubber band around the end of the tube pull it tight under the jaws and anchor it in the material keeper on the top of the vice .
Cheap and easy fix.

09-05-2004 10:35 AM
1 More Cast
Tying Tube Flies Question:

When tying tube flies on a mandral, i was wondering if the tube is suppose to rotate on the mandral? I am using a devise ( I don't know the make of this tool) that fits into the jaws of my vise and has 3 differant size mandrals. I am using a combination of plastic, alumunim, and brass tubes. When tying the tubes will rotate, this makes attaching materials and wrapping difficult. This is my first attempt at tying tubes, any advice would be greatly appreciated.
1 More

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 10:02 AM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright (All Rights Reserved)