|11-03-2004 03:46 AM|
I can't wait to get to the vice to tie some up, and get after those grayling!
|11-02-2004 06:18 AM|
Sorry guys about the late reply,
The beads are tied with a (flattened) piece of mono underneath the hook.
They fit in nicely in the bent-shape of these hooks. It's a quite simple way of tying in fact. After securing the bead you can tye the rear part of the nymph as usual. If you get close to the bead you can tye in the legs by using a dubbing loop. This loop can be wrapped around the hookshank, behind the bead (on top a bit more to the front of the fly), or around the top of the bead itself. If you do so you must make sure to leave this top of the bead, closest to the shank, as clear as possible. If not the loop will slip over the bead. Finishing the thorax is standard again.
What I like most about this system is that it's very simple, highly effective and that it might be a challenge for fly tiers to adapt known successful patterns into up-side down ones, which I aspect to be even better. For the patterns I tried it works great (Montana, Pheasant Tail and some un-identified owns patterns, as the second pic shows) I'm always curious about your adapted patterns to this tying style.
BTW I am thinking about contacting some magazines now to see if they are interested in some publications in order to share it more widely.
|10-30-2004 02:57 AM|
The flies look great - I am just about to start winter grayling fishing here in Scotland, and would love a close look at these flies. If possible, could you drop me an e-mail?
Would love to try them soon!
|10-18-2004 01:39 PM|
I'd be interested in seeing a PT style...
Do you actually use mono or are the beads put on the shank as normal?
|08-24-2004 12:42 PM|
Holy be-jebus that is nuts. Very awesome looking fly.
good luck with them.
|08-24-2004 09:28 AM|
other hook brands
Daiichi makes a swimming nymph hook in bronze with a profile very similar to that depicted in the photos. The model number is 1770 and it is available in sizes 6 through 16. If you call Daiichi direct at 800.332.3305 and ask nicely they may send a sample pack for you to try.
If a shorter body is desired, one may want to experiment with the 2170 (1x short, bent shank, standard wire, straight-eye). It's not available in the same size range nor does it have as pronounced of a bend but it may work when smaller beads are used to make smaller nymphs while still having a decent-sized gape to hold fish.
Very nicely tied and ingenious pattern, by the way.
Daiichi Pro Staff
|08-11-2004 08:39 PM|
|John Desjardins||Nice fly. I can't remember seeing a fly with a bead tied in this way.|
|08-11-2004 06:16 PM|
looks like it would tick the bottom very seductively...
Very cool tie, a definite curve ball for fish.
|08-11-2004 11:25 AM|
The ones shown here were tied on TMC T400 hooks. These are , as far as I know, only available in sizes 10, 12 and 14 (so not that very small). But it's form looks as if made especially for it. If interested I can post two patterns (Montana-type and Pheasant tail type) with which most nymphs can be adapted to this "bubble-type".
Íf you are gone use them I would like to know about your results.
|08-11-2004 10:40 AM|
I can honestly say that I've never seen a nymph tied that way before. It looks like a bead strung on a piece of mono, which is then secured at both ends.
I know some fish that get pounded on a regular basis that might like these, just because they're so different.
|08-11-2004 10:15 AM|
up-side-down nymphs (bubble nymphs)
What do you think of these nymphs ? Or rather of the way they are tied, as with this method you can adapt about every known pattern to swim hookbent-up.
(they perform very well, I asked many trout and other species)
Like to hear from you.