Fly Fishing Forum - Reply to Topic
>> Archive: Striper (etc) Flies Tricks of the trade

Thread: Epoxy Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Home Waters
Your home waters
Current Favorite Fly
If you only had one... (change anytime)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
09-29-2000 03:12 PM

I also use the devcon bottle, and am about a third of the way through the bottles after two years with them.

I find that a fast steady stir, like beating eggs, gets rid of teh bubbles.

I also have personally dispelled the wood utensil yellowing myth--I use wood coffee sirrers, snip the end at a 45 degree angle so there is a point to it, and mix all my epoxy on yellow post it note pads and never have any discoloration problems...

09-26-2000 02:24 PM
Nathan Smith

Apoxy suggestions

1. Less Bubbles, Mix slow and in one direction. This removes some of the bubbles
2. Bulk, Devcon is nice. Actually I have gone to the two part that comes in the single dispencer, it is more expensive per ounce but easier to use and alway mixes in the right parts
3. Which Type, the longer the drying time the harder and clearer it is. The 1 minute is a bad choice I think because it tends to yellow and doesn't last very long. That is important when you are making stuff like surf candy which lasts for ever. 5 minute is the most popular. I use it the most. 10 would be a better choice then 20 minute. If you are going to use 10 or especially 20min you have to have an electric turner or you will be sitting there for ever.
09-23-2000 08:23 PM

Roop -

Devcon makes a nice two-part bulk 5 minute epoxy. It comes with two ketchup squeezer style bottles in a blue and white box. Mine has lasted about 3 years so far. Bubbles are not a problem if mixed using a popsicle stick style stick (I use starbuck's stirrers). The rumor that wood causes yellowing is not true. The secret (according to scientists at 3M corporation who took my inquiry VERY seriously) to keeping a clear mixture is the mixture itself, in other words having too much catalyst will yellow the mix. Ultraviolet light is also a big factor. In fact, 3M provides a wooden stir stick with many of their products.

I'll take a look on the box for the part no. etc. I have seen it at hardware, hobby and fly shops. I am certain Smitty will have it at the Rod Builder's Workshop in Kingston (781) 582-1015. His place always smells like glue with all the rods being built.

Softex has its place too. Talk about smell!
09-23-2000 03:59 PM

Mr. Pink,

I have been primarily using it to finish the heads of my baitfish patterns and really like the way it brings out the color of the materials/ brings the color to the surface. That's why I would like to find it in larger containers than the 2-part syringe.

Anyway, I just squirt a small amount into a dixie cup & mix with a coffee stirrer. I start off by putting a small drop where each of the eyes will go, get those where I want and then using small dollops again, work the epoxy around the edges of the eyes, filling the void between them and then down the nose to the eye of the hook, slowlly pulling it along.

Based upon the quality of the sample flies of yours I've seen, I find it hard to believe that there are really any noticeable bubbles in your finished products.

Maybe it's the epoxy. Lately I've been using Superglue's 5 min. epoxy and really like it - it has a crystal clear finish.

Dave P also suggests 20 minute epoxy, Domenic recommends 1 minute.

I've also read about Red Devil having an acrlyic caulk that dries clear and is much easier to use - haven't found it yet.

Good luck.

PS - I'm always ready to play hooky!

09-22-2000 06:37 PM
Bob Pink

One of the common uses for epoxy is to build heads on flies. One of the things that always frustrates me are the microbubbles that get trapped in the mix. I've tried heating the mix (a la page rogers) but it shortens the working time so much it's only good for one fly.
Any technique that you use to get a clear finish?
09-21-2000 06:52 PM

I've finally started toget the hang of 5 minute epoxy.

Does anyone know where to find it in bulk?



Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 04:19 PM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright (All Rights Reserved)