Fly Fishing Forum - Reply to Topic
>> Archive: Warmwater Gamefish Flies Freshwater Bass, pike, muskie?!?

Thread: Pike Crease flies Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
03-11-2003 06:25 PM
Dble Haul Here's a second fly, tied with the same materials and methods....
03-11-2003 06:24 PM
Dble Haul
Pike Crease flies

Pete was very generous and sent a few crease flies to test out on the rivers in my area. Here's the recipe and instructions as detailed by Pete in his own words.

Thanks Pete!

Body: Craft foam. I tried pink, yellow, and white. I prefer the white so far.
Shell: Iridescent wrapping paper. I tried various metallic wrapping papers but they are too opaque and donít seem to stick well to the foam body.
Color: Various permanent markers.
Hook: TMC 511S size 2/0
Tail: Assorted synthetic fiber with flashy materials
Underbody: Magik Glitter glue

Assembly:

1. Make a paper pattern
2. Mark off several body shapes on the foam.
3. Tape over the shapes with carpet tape. This stuff is a very fine film of sticky material, also known as 2-way tape. The tape is only 2 inches wide and you need 2X width to cover the fly body, or 3X depending on which orientation you use, length or width. Make sure to put one strip on at a time, that is place it on the foam and remove the cover tape before placing the next strip.
4. Cut out some iridescent shell and carefully place it on the body. If you want a variation on the body, just crinkle the paper in your hands, then apply it.
5. Rough cut each body shape, then detail cut each one.
6. Paint the shell with the markers, starting with the top line and then the lateral line, blending as you go along.
7. After the marker coloration is dry, bend the shell into a crease and hold for a few minutes with wooden clothes pins. I did three at a time. I colored the inside of the shell, at the front end, about one quarter from the face towards the tail rather than leaving it white.
8. Prepare the tail. I made the tails very sparse due to the teeth foul-ups common with pike. Just take a little bit of flash and a little bit of hair, wrap it with tying thread about one quarter inch and put it aside. This really helps when finishing the fly.
9. Open up the creased shell, apply cryo glue around the edges and in the middle part where the tail and hook will go. The tail is not tied onto the hook.
10. Place the tail into the crease, close it, and hold it with two clothes pins.
11. Place the hook inside and then hold it with three or more clothes pins. I leave the mouth open to create more water disturbance and make the fly swim more erratically.
12. After the fly glue is dry, about 30 minutes, place the tape eyes on and apply a fine bead of Sparkle glue to the foam section of the underfly. This glue will not stay on if applied to the body, and takes a long time to fully dry.
13. I used some poly-urethane clear varnish to overcoat the fly, two coats.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:10 PM.



Copyright Flyfishingforum.com (All Rights Reserved)