Fly Fishing Forum - Reply to Topic
the Rod Rack Rod Builder's Forum

Thread: Replacing cork grips and reel seat Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
10-25-2004 11:05 PM
Stephen Asher
Re-treads

Marketic: Great reply! Yes, the Spey rod in question is carbon fiber/ graphite. Thanks. Parenthetically, I purchased my first new (also English)cane rod in the early 1960's and the last in the mid 70's. Since the advent of modern carbon fiber rods (Scott G series for me ), cane has not seen water. While I own a Dremel with cutting heads, I will need to venture into this "gripping" experience with an experienced hand. Will keep you posted and thanks again. SWA
10-25-2004 10:51 PM
marketic
Re-Treading a Double Fister

hello, Stephen

You did not mention if the rod you would like to modify is cane or composite. Either way, it is not all that difficult to strip the corks and reel seat off ANY rod and replace them (although if your rod is cane (bamboo) the bigger concern would be the possibility of negatively effecting its value by this type of modification.

I was forced to modify several of my rods because I use antique fly reels with longer reel feet. These larger older reels require custom-made reel seats. But I never had to worry about negatively effecting the value of these rods I was modifying because I built them all originally to begin with. Thus, it turned out to be a sorely needed up-grade that in essence increased the value (for me, anyway).

I cannot recommend someone who can modify your rod for you. But I can tell you it's very easy to do yourself and you should consider it.

The magic tool that will guarantee good results: a Dremel with a cutting disk attachment. The hardest part of stripping harware off a rod is the reel seat. But a Dremel takes care of that in several minutes. CAUTION: just don't nick the rod underneath the seat when you're making the cut. If the nick is deep enough you could damagae the rod.

Anyway:

Step 1 = remove the stripping guides on the butt section (if necessary) Razor blade: gently cut the threads, remove guide(s), clean rod surface beneath them.

Step 2 = remove corks of foregrip. Sharp knife, razor blade, whatever is necessary to completely remove cork

Step 3 = remove reel seat. Take off tightening rings if down-locking seat. Dremel and disk grinder: with a spiral cut starting from top of seat, work your way down to the bottom of the seat, taking care to only go deep enough to cut the reel seat itself. Usually there are tape shims beneath the seat so there is an insurance policy in place. But with no guarantee of that, USE CAUTION

Once spiral cut is made, peel (or pry) off reel seat

Step 4 = remove corks on butt (and butt cap if there is one)

Step 5: sand the entire butt surface then prepare to replace the following IN THIS STRICT ORDER

a)) butt grip b)) reel seat c)) foregrip d)) stripping guides

Any rod building manual will describe how to do this properly

Replacing guides is easy. Getting the wraps to look like the rod's original wraps is a bit more of a challenge but not insurmountable.

GOOD LUCK and remember the Dremel !
10-25-2004 09:40 PM
Stephen Asher
Replacing cork grips and reel seat

Recently, I have purchased a well respected British Spey 15 foot 10/11 wt rod ( it must remain nameless ) with a sweet yet powerful action. The quality of the rod far exceeds the quality of the reel seat (also nameless) . Further, the upper section of the grip has a bulge about three inches below its top. I find it is uncomfortable and, more importantly, it is difficult to release shooting line with this bulge. I prefer a straighter grip such as on my T&T and Loop.
I have never buuilt a rod so perhaps my question is obvious. Can I remove the current grips and reel seat and replace them with more fitting and cosmetically appropriate items, without damaging the rod's integrity?? I would not plan to do this myself so could you suggest a person to do so??
Many thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:45 PM.



Copyright Flyfishingforum.com (All Rights Reserved)