Fly Fishing Forum - Reply to Topic
Gear Talk - Fly Stuff Spoken Here Sage advice & fresh perspectives

Thread: Fly falling apart, what can I use/do? Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Fly Fishing Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Home Waters
Your home waters
Current Favorite Fly
If you only had one... (change anytime)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options
Rate Thread
If you like, you can add a score for this thread.

Topic Review (Newest First)
08-31-2000 10:42 AM
RE:Fly falling apart, what can I use/do?

Back cast - hadn't even occured to me and you're both probably right on with that. I'll have to look back while I'm casting and watch.

Should probably coat the flies anyway, these are ones I've purchased and they're very nice ones, so I don't want to trash them in one outing.
08-30-2000 08:06 PM
RE:Fly falling apart, what can I use/do?

I've used fabri-tac, zap-a-gap, epoxy, and sof-tex all with great success. I have also used clear fingernail polish with not as great success. BTW clear fingernail polish painted on your watch face saves it from scratches. When the finger nail polish gets scratched you either remove the old and coat again or just add another coat.

As Juro stated, I bet your biggest culprit in the falling apart fly is the back-cast.
08-30-2000 06:21 PM
RE:Fly falling apart, what can I use/do?

Without seeing it, I can suggest a couple things:

a) you can go for a slightly thinner thread and use more wraps, crisscrossing and wrapping fore and aft to keep eyes straight. A couple drops of zap-a-gap (a common hobby store superglue) will turn it into steel if you have enough of a thread base.

b) coat with epoxy being careful not to load it up too thick to throw off the profile and balance (aesthetic) of the sand eel fly.

c) use quality eyes, I use "real eyes" because they are steel (vs. soft lead) and have a deep vee in the middle. They also have recessed eye sockets to allow sticker eyes (match the diameter w/ clearance) to be applied without glue.

d) watch the back cast, most eyes are lost on the back cast as opposed to the bottom - unless it's a rocky bottom (as opposed to sand or gravel).

e) use a bendback hook instead of weighted eyes to tie the fly - it'll ride point up if you tie in the material correctly. Put more material on the side you want to ride up, especially if it's bucktail or other hollow natural hair. You will need the sinking line to get it down but it will glide on the bottom without snagging.
08-30-2000 05:41 PM
Fly falling apart, what can I use/do?

Some flies I use with a sinking line must be dragging on the bottom because the threads holding the dumb bell eyes on are coming apart (and hence the eyes fall off).

Can I coat these with something without hurting the material? Nail polish?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 10:03 PM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright (All Rights Reserved)